Tel: +86-532-83130887 Email: eiffel@qdhaijia.net
| Quantity: | |
|---|---|
HW-6012
Haijia
Company Introduction
For a long time, Haijia always walks in the forefront of the industry in product research and development, technological innovation, and is the leading enterprise in China's water jet loom industry. As appraised by the expert group of China Federation of Textile Industry, Haijia produces products with technological level reaching the international advanced, and possesses nearly 150 independent intellectual property rights, including 24 patents of invention (5 patents of invention in foreign countries), and has 12 registered trademarks, including 5 international trademarks.
Water jet Configuration
The integrated wall plate optimizes the design of the frame structure, weft beating mechanism, and opening device, and the loom's high speed and stability are considerably enhanced over the original form.
The revised design of the weft guiding system improves weft guiding efficiency and responds to high speed weft guiding.
The "U" type weft beating shaft and a special weft beating balance system are used, and the weft beating shaft has multiple reinforced support seats and a centralized lubrication system to increase weft beating force, decrease weft beating shaft wear, and extend the loom's service life.
Suitable for Twisted chiffon,Nylon taffeta,Spandex, Down jacket fabric，etc.
| Water Jet Loom Configuration Table | |||
Model | HW3851、HW3873、HW600、HW6010、HW6012、HW8010、HW8030 | ||
reed width | Nominal reed width(cm) | 150、170、190、210、230、270、280、290、300、320、340、360 | |
Effective reed | Nominal reed width：0～65cm(≤230cm);0～85cm（＞230cm) | ||
Weft selection | 1color、2 colors、3 colors、4 colors | ||
power | Starting mode | Direct drive motor | super start motor drive |
Motor capacity | 2.2KW、2.7KW、3.0KW、3.7KW、4.5KW、6.0KW | ||
running operation | One-hand operation button | Two-hand operation button | |
Weft insertion | pump | single pump | double pump |
nozzle | Normal nozzle,'U'nozzle | ||
Length measurement and weft storage | Electronic Length Measurement (FDP) | （RDP)Mechanical length measurement | |
shedding | Crank shedding: 4-piece type, 6-piece type | 8-piece type | |
Positive cam shedding: 6, 8, 10 piece type | 12,14 piece type | ||
Active dobby: 16 piece type | |||
let-off | negative loose warp | Positive loose warp device | |
Left and right double bearing, 2-roll mode | |||
Maximum tension | 500Kg、1000Kg | ||
diameter of the beam flange | ∮800mm | ∮914mm、∮1000mm | |
take-up | Roll cloth diameter | maximum is 520MM | |
cloth roll path | S type, L type | ||
Beating-up shaft | Crank multi reed sley beating up mechanism, "U" shaped beating up shaft | Solid straight shaft beating up | |
4 linkage,6 linkage | |||
Weft stand | Floor fixed type 2 barrels/color | ||
Selvage | Mechanical planetary mode | ||
Yarn end treatment | Spindle false twisting method | ||
Weft cutting | Mechanical scissors for weft cutting | ||
dehydration | Suction mode of micro slit tube (electric water suction motor), buoyancy air-water separator | Water absorbing strip | |
electronic gadgetry | Optical fiber type feeler | Photoelectric type | |
Touch screen, control preparation, start, stop, inching and reverse inching | |||
It can display output, speed, efficiency, shutdown times, etc | |||
The four-color indicator light indicates the reason for stopping | |||
Variable inverter/variable speed device | |||
Automation and labor saving | Automatic water replenishment valve, automatic centralized refueling | Variable frequency speed regulation | |
What's The difference between Hollow beat-up shaft and Solid beat-up shaft?
Hollow beat-up shaft and can be equipped with 114 and 159 hollow tubes according to the width and fabric. The bearings on both sides can be equipped with double bearings to better decompose the radial force generated by the beat-up and ensure the high-speed and smooth operation of the loom.
Solid beat-up shaft and split counterweight block structure: By adding or subtracting counterweight blocks and combining the movement of the wall board box, different beat-up forces can be produced to meet the needs of different widths and fabrics.
Company Introduction
For a long time, Haijia always walks in the forefront of the industry in product research and development, technological innovation, and is the leading enterprise in China's water jet loom industry. As appraised by the expert group of China Federation of Textile Industry, Haijia produces products with technological level reaching the international advanced, and possesses nearly 150 independent intellectual property rights, including 24 patents of invention (5 patents of invention in foreign countries), and has 12 registered trademarks, including 5 international trademarks.
Water jet Configuration
The integrated wall plate optimizes the design of the frame structure, weft beating mechanism, and opening device, and the loom's high speed and stability are considerably enhanced over the original form.
The revised design of the weft guiding system improves weft guiding efficiency and responds to high speed weft guiding.
The "U" type weft beating shaft and a special weft beating balance system are used, and the weft beating shaft has multiple reinforced support seats and a centralized lubrication system to increase weft beating force, decrease weft beating shaft wear, and extend the loom's service life.
Suitable for Twisted chiffon,Nylon taffeta,Spandex, Down jacket fabric，etc.
| Water Jet Loom Configuration Table | |||
Model | HW3851、HW3873、HW600、HW6010、HW6012、HW8010、HW8030 | ||
reed width | Nominal reed width(cm) | 150、170、190、210、230、270、280、290、300、320、340、360 | |
Effective reed | Nominal reed width：0～65cm(≤230cm);0～85cm（＞230cm) | ||
Weft selection | 1color、2 colors、3 colors、4 colors | ||
power | Starting mode | Direct drive motor | super start motor drive |
Motor capacity | 2.2KW、2.7KW、3.0KW、3.7KW、4.5KW、6.0KW | ||
running operation | One-hand operation button | Two-hand operation button | |
Weft insertion | pump | single pump | double pump |
nozzle | Normal nozzle,'U'nozzle | ||
Length measurement and weft storage | Electronic Length Measurement (FDP) | （RDP)Mechanical length measurement | |
shedding | Crank shedding: 4-piece type, 6-piece type | 8-piece type | |
Positive cam shedding: 6, 8, 10 piece type | 12,14 piece type | ||
Active dobby: 16 piece type | |||
let-off | negative loose warp | Positive loose warp device | |
Left and right double bearing, 2-roll mode | |||
Maximum tension | 500Kg、1000Kg | ||
diameter of the beam flange | ∮800mm | ∮914mm、∮1000mm | |
take-up | Roll cloth diameter | maximum is 520MM | |
cloth roll path | S type, L type | ||
Beating-up shaft | Crank multi reed sley beating up mechanism, "U" shaped beating up shaft | Solid straight shaft beating up | |
4 linkage,6 linkage | |||
Weft stand | Floor fixed type 2 barrels/color | ||
Selvage | Mechanical planetary mode | ||
Yarn end treatment | Spindle false twisting method | ||
Weft cutting | Mechanical scissors for weft cutting | ||
dehydration | Suction mode of micro slit tube (electric water suction motor), buoyancy air-water separator | Water absorbing strip | |
electronic gadgetry | Optical fiber type feeler | Photoelectric type | |
Touch screen, control preparation, start, stop, inching and reverse inching | |||
It can display output, speed, efficiency, shutdown times, etc | |||
The four-color indicator light indicates the reason for stopping | |||
Variable inverter/variable speed device | |||
Automation and labor saving | Automatic water replenishment valve, automatic centralized refueling | Variable frequency speed regulation | |
What's The difference between Hollow beat-up shaft and Solid beat-up shaft?
Hollow beat-up shaft and can be equipped with 114 and 159 hollow tubes according to the width and fabric. The bearings on both sides can be equipped with double bearings to better decompose the radial force generated by the beat-up and ensure the high-speed and smooth operation of the loom.
Solid beat-up shaft and split counterweight block structure: By adding or subtracting counterweight blocks and combining the movement of the wall board box, different beat-up forces can be produced to meet the needs of different widths and fabrics.
