Tel: +86-532-83130887 Email: eiffel@qdhaijia.net
Optimized design of the weft beating mechanism and opening device with the newly developed "U" type short pitch nozzle further improves the weft drawing performance based on the ultra-high speed performance.
The new strong frame structure and enhanced warp feeding device shorten the path of the fabric surface before weaving and significantly improve the weft beating performance, especially the six-link weft beating, which achieves high speed and high quality at a higher level.
The adjustable axial clearance of the warp feeding worm gear enables the stability of the warp feeding device, which can be adapted to wide and dense fabrics, and can handle special specifications from very fine to coarse yarns, from narrow to wide widths, and from general fabrics to double fabrics.
U-shaped weft beating shaft and special weft beating balance system. The weft beating shaft is equipped with multiple reinforced supports and centralized lubrication system, which improves the weft beating force and weft beating shaft wear, increasing the service life of the weaving machine.
The redesigned frame structure, with a tilted warp path from the weaving mouth, shortens the weaving surface path, enables stable weaving even at higher densities and reduces the warp position line to 900 mm, which is in line with the ergonomic operation theory and significantly improves the weft beating performance and weaver control. The weaving machine speed can be changed by simple parameter setting, and the weft density and speed can be changed for complicated fabrics.
The maximum design speed can reach 1400RPM
Adopt double pumps and four nozzles to improve work efficiency
| Water Jet Loom Configuration Table | |||
Model | HW3851、HW3873、HW600、HW6010、HW6012、HW8010、HW8030 | ||
reed width | Nominal reed width(cm) | 150、170、190、210、230、270、280、290、300、320、340、360 | |
Effective reed | Nominal reed width：0～65cm(≤230cm);0～85cm（＞230cm) | ||
Weft selection | 1color、2 colors、3 colors、4 colors | ||
power | Starting mode | Direct drive motor | super start motor drive |
Motor capacity | 2.2KW、2.7KW、3.0KW、3.7KW、4.5KW、6.0KW | ||
running operation | One-hand operation button | Two-hand operation button | |
Weft insertion | pump | single pump | double pump |
nozzle | Normal nozzle,'U'nozzle | ||
Length measurement and weft storage | （FDP）Electronic Length Measurement (FDP) | （RDP)Mechanical length measurement | |
shedding | Crank shedding: 4-piece type, 6-piece type | 8-piece type | |
Positive cam shedding: 6, 8, 10 piece type | 12,14 piece type | ||
Active dobby: 16 piece type | |||
let off | negative loose warp | Positive loose warp device | |
Left and right double bearing, 2-roll mode | |||
Maximum tension | 500Kg、1000Kg | ||
diameter of the beam flange | ∮800mm | ∮914mm、∮1000mm | |
take up | Roll cloth diameter | maximum is 520MM | |
cloth roll path | S type, L type | ||
Beating-up | Crank multi reed sley beating up mechanism, "U" shaped beating up shaft | Solid straight shaft beating up | |
4 linkage,6 linkage | |||
Weft stand | Floor fixed type 2 barrels/color | ||
Selvage | Mechanical planetary mode | ||
Yarn end treatment | Spindle false twisting method | ||
Weft cutting | Mechanical scissors for weft cutting | ||
dehydration | Suction mode of micro slit tube (electric water suction motor), buoyancy air-water separator | Water absorbing strip | |
electronic | Optical fiber type feeler | Photoelectric type | |
Touch screen, control preparation, start, stop, inching and reverse inching | |||
It can display output, speed, efficiency, shutdown times, etc | |||
The four-color indicator light indicates the reason for stopping | |||
Variable inverter/variable speed device | |||
Automation and labor saving | Automatic water replenishment valve, automatic centralized refueling | Variable frequency speed regulation | |
Optimized design of the weft beating mechanism and opening device with the newly developed "U" type short pitch nozzle further improves the weft drawing performance based on the ultra-high speed performance.
The new strong frame structure and enhanced warp feeding device shorten the path of the fabric surface before weaving and significantly improve the weft beating performance, especially the six-link weft beating, which achieves high speed and high quality at a higher level.
The adjustable axial clearance of the warp feeding worm gear enables the stability of the warp feeding device, which can be adapted to wide and dense fabrics, and can handle special specifications from very fine to coarse yarns, from narrow to wide widths, and from general fabrics to double fabrics.
U-shaped weft beating shaft and special weft beating balance system. The weft beating shaft is equipped with multiple reinforced supports and centralized lubrication system, which improves the weft beating force and weft beating shaft wear, increasing the service life of the weaving machine.
The redesigned frame structure, with a tilted warp path from the weaving mouth, shortens the weaving surface path, enables stable weaving even at higher densities and reduces the warp position line to 900 mm, which is in line with the ergonomic operation theory and significantly improves the weft beating performance and weaver control. The weaving machine speed can be changed by simple parameter setting, and the weft density and speed can be changed for complicated fabrics.
The maximum design speed can reach 1400RPM
Adopt double pumps and four nozzles to improve work efficiency
| Water Jet Loom Configuration Table | |||
Model | HW3851、HW3873、HW600、HW6010、HW6012、HW8010、HW8030 | ||
reed width | Nominal reed width(cm) | 150、170、190、210、230、270、280、290、300、320、340、360 | |
Effective reed | Nominal reed width：0～65cm(≤230cm);0～85cm（＞230cm) | ||
Weft selection | 1color、2 colors、3 colors、4 colors | ||
power | Starting mode | Direct drive motor | super start motor drive |
Motor capacity | 2.2KW、2.7KW、3.0KW、3.7KW、4.5KW、6.0KW | ||
running operation | One-hand operation button | Two-hand operation button | |
Weft insertion | pump | single pump | double pump |
nozzle | Normal nozzle,'U'nozzle | ||
Length measurement and weft storage | （FDP）Electronic Length Measurement (FDP) | （RDP)Mechanical length measurement | |
shedding | Crank shedding: 4-piece type, 6-piece type | 8-piece type | |
Positive cam shedding: 6, 8, 10 piece type | 12,14 piece type | ||
Active dobby: 16 piece type | |||
let off | negative loose warp | Positive loose warp device | |
Left and right double bearing, 2-roll mode | |||
Maximum tension | 500Kg、1000Kg | ||
diameter of the beam flange | ∮800mm | ∮914mm、∮1000mm | |
take up | Roll cloth diameter | maximum is 520MM | |
cloth roll path | S type, L type | ||
Beating-up | Crank multi reed sley beating up mechanism, "U" shaped beating up shaft | Solid straight shaft beating up | |
4 linkage,6 linkage | |||
Weft stand | Floor fixed type 2 barrels/color | ||
Selvage | Mechanical planetary mode | ||
Yarn end treatment | Spindle false twisting method | ||
Weft cutting | Mechanical scissors for weft cutting | ||
dehydration | Suction mode of micro slit tube (electric water suction motor), buoyancy air-water separator | Water absorbing strip | |
electronic | Optical fiber type feeler | Photoelectric type | |
Touch screen, control preparation, start, stop, inching and reverse inching | |||
It can display output, speed, efficiency, shutdown times, etc | |||
The four-color indicator light indicates the reason for stopping | |||
Variable inverter/variable speed device | |||
Automation and labor saving | Automatic water replenishment valve, automatic centralized refueling | Variable frequency speed regulation | |
